Heat Treatment Cost Calculator
Heat treatment is quoted as a price per kilogram plus a minimum charge per batch, so at low volumes the minimum — not the weight — sets the unit price. This calculator separates the weight charge, the batch minimum, straightening, hardness testing and inbound freight, and returns both a per-part and a whole-batch figure.
Batch total — CNY · effective rate — CNY/kg
Error range ±30%. Heat treatment prices vary widely with furnace type, loading method and region: vacuum, sealed-quench and continuous furnaces are not the same market. The model prices by weight and ignores loading density — thin plates and long shafts occupy furnace volume without weight, so their real rate per kilogram is higher.
How the cost is built up
- Heat treatment — batch weight × rate, compared with the batch minimum, then divided by the batch size. At low volumes the minimum almost always wins.
- Straightening and fixturing — distortion scales with length-to-diameter ratio; long shafts and thin walls cost most. Nitriding and black oxide rarely need it.
- Hardness testing — a few checks per batch, charged per batch and spread across the parts.
- Freight share — outsourced treatment means a round trip, charged per part or per kilogram.
Formulas
batch weight = part weight × batch size
weight charge = batch weight × rate
batch treatment = max(weight charge, batch minimum)
treatment / part = batch treatment ÷ batch size
testing / part = tests × fee ÷ batch size
total / part = treatment + straightening + testing + freight Worked example
0.8 kg 45-steel part, 200 pieces, quench and temper (¥6.50/kg, min ¥100), ¥0.30 straightening, two tests at ¥30:
| Batch weight (160 kg × ¥6.50 = ¥1040, above the minimum) | ¥5.20 / part |
| Straightening and fixturing | ¥0.30 |
| Hardness testing (¥60 ÷ 200) | ¥0.30 |
| Freight share | ¥0.05 |
| Total | ¥5.85 / part (batch ¥1,170) |
Now set the batch to 10: the batch weighs 8 kg, the weight charge is ¥52, below the ¥100 minimum, so treatment is billed at ¥100 ÷ 10 = ¥10 per part. The total jumps to ¥16.35 (testing is spread over 10 parts too) and the effective rate becomes ¥12.50/kg — nearly double the list price. That is where “small batch surcharge” on a heat-treatment quotation comes from.
In-house versus outsourcing
A heat-treat line is heavy capital: a box furnace with quench tank, a tempering furnace and a hardness tester starts in the hundreds of thousands, plus a process engineer. Unless the product mix is stable and volume runs to tens of tonnes a month, outsourcing wins — their price already carries furnace depreciation, but you carry no fixed cost. The test is simple: compare the outsourced rate × annual weight against in-house depreciation, energy and labour.
Not included
- Dye penetrant, metallography and third-party inspection reports
- Rework from out-of-spec case depth, and re-treatment
- Post-treatment blasting, shot peening and rust prevention
- Machining rework caused by distortion
- Expedite fees and night-shift surcharges
Common questions
Why is heat treatment priced per kilogram?
Because furnace cost follows the weight loaded: how many kilograms per cycle, how much gas and power. The number of parts barely matters. A supplier quoting per part is really estimating part weight and loading density for you.
What is a typical batch minimum?
¥50–200 per batch for plain hardening, ¥200–500 for carburising and nitriding, ¥300–800 for vacuum hardening. Above a few hundred parts the minimum fades; below it, it is the whole price.
Does everything need straightening after quenching?
Parts with high length-to-diameter ratio, asymmetric sections or thin walls almost always do. Short, stout parts, or those ground afterwards with allowance, often do not. Straightening is manual press work: a few tenths of a yuan to a few yuan per part.
Carburising or nitriding?
Carburising gives a deeper case (0.3–1.5 mm) with a gentler hardness gradient at moderate cost — gears and shafts. Nitriding gives a thin, harder, low-distortion case (0.1–0.3 mm) at low temperature, suited to finish-machined parts, but cycles are long and the rate is higher.