Stamping Die Cost Estimator
The stamping cost calculator takes tooling cost as an input, but a quotation rarely tells you what a die is worth beyond the words "one set". This tool fills that gap: from blank size and station count it splits a tool into die set, working steel, machining hours and tryout, so you can tell whether a tooling quote is in the right order of magnitude before you negotiate.
1. Inputs
| Die set (plates, guide pins and bushes) | — CNY |
| Working steel | — CNY |
| Machining and assembly | — CNY |
| Tryout and tuning | — CNY |
| Die working area (50 mm margin included) | — cm² |
| Total machining hours | — h |
| Combined factor (type × precision × volume) | — × |
±35%. Tooling is quoted, not computed: the same drawing differs twofold between regions, suppliers and whether design is in-house. Use this to place a quote in the right order of magnitude and to see which line item eats the budget — not to argue a supplier down to the yuan.
Formula
die area (cm²) = (blank length + 100) × (blank width + 100) ÷ 100
die set (CNY) = 2500 + 5 × die area
steel (kg) = die area × 4.0 cm × 7.85 g/cm³ ÷ 1000
steel (CNY) = steel kg × 28
hours per station = 40 + 0.12 × die area^0.8
machining (CNY) = hours per station × stations × 200
tryout (CNY) = stations × 2 passes × 4 h × 400 CNY/h
total (CNY) = (die set + steel + machining + tryout)
× type × precision × volume factor The 100 mm added to each dimension is the 50 mm margin a die set needs on all four sides. The power term 0.12 × area0.8 says that machining hours grow slower than area: a large die is cut in one setup on a gantry mill, while a small one spends a larger share of its time on clamping and edge finding.
What each input means
- Stations — blanking, piercing, forming, bending, flanging and sizing each count as one. In a progressive die that equals the number of stations; in a single-operation die it equals the number of separate tools, so 3 stations means three die sets' worth of machining hours.
- Die type — a progressive die adds strip feed, lifters and locating pilots, and needs a thicker, stiffer set: 25% over a single-operation tool at the same station count. A compound die adds only 10%, limited by how many actions one stroke can complete.
- Volume tier — low volume runs on Cr12MoV-class steel; past 500k parts a year you move to SKD11/D2 with vacuum hardening and coating, which lifts both material and heat treatment 20%.
- Precision class — 0.01 mm fits, burr height and flatness tolerances double the wire-EDM and jig-grinding hours.
Worked example
300 × 200 mm blank, 3-station progressive die, medium volume, standard precision (the page defaults):
| Die area | (300+100) × (200+100) ÷ 100 = 1200 cm² |
| Die set | 2500 + 5 × 1200 = 8,500 CNY |
| Working steel | 1200 × 4 × 7.85 ÷ 1000 = 37.68 kg → × 28 = 1,055 CNY |
| Hours per station | 40 + 0.12 × 12000.8 = 40 + 34.88 = 74.88 h |
| Machining | 74.88 × 3 × 200 = 44,926 CNY |
| Tryout | 3 × 2 × 4 × 400 = 9,600 CNY |
| Subtotal | 8,500 + 1,055 + 44,926 + 9,600 = 64,081 CNY |
| Total | 64,081 × 1.25 = ¥80,101 |
Varying one condition at a time, with everything else unchanged:
| Single-operation die, low volume | 64,081 × 1.00 × 0.90 = ¥57,673 |
| Precision class, high volume | 64,081 × 1.25 × 1.25 × 1.20 = ¥120,151 |
| 3 → 5 stations | machining 74.88 × 5 × 200 = 74,876; tryout 16,000; subtotal 100,431 → ¥125,539 |
Note the second row: precision and volume multiply the whole subtotal, not just the steel. In reality precision shows up mostly in machining hours and volume mostly in steel and heat treatment — the factor method is deliberately coarse. Do not use it as a line-item cost sheet.
Four mistakes that skew the number
- Using the finished part size instead of the blank — a bent part has a much larger blank, so the die set and steel are both underestimated by a full size step.
- Forgetting the number of tools — with single-operation dies, stations equal tool count; quoting 4 stations and budgeting one die set is wrong.
- Treating tooling as a one-off cost — it must be amortised over die life; use the amortisation line in the stamping cost calculator.
- Ignoring modifications — moving one hole after PPAP means stripping and re-cutting; die changes typically run 10%–30% of the original tool cost and are not included here.
Not included
- Die design, usually quoted separately at 8%–15% of the tool cost
- Automatic strip feed, robots, scrap conveyors and other peripherals
- Trial material scrap and press time lost to tryout (only press hours are counted)
- Freight, tax, on-site installation and warranty service
- Carbide inserts, nitrogen springs, imported guide pillars and similar upgrades
FAQ
Why is a progressive die dearer at the same station count?
Because it packs N operations into one die set: plates must be thicker for rigidity, the strip feed needs accurate pitch, every station needs lifters and pilots, and assembly and tuning grow faster than station count. The extra 25% buys one press, one setup and a stable cycle — at volume that saves more press hours than the tool difference.
Why is the station count capped at 12?
Beyond roughly 12 stations the part usually should not be run in a single progressive tool, or it needs splitting across two dies in sequence. The cap keeps the estimate inside the range where the model is still meaningful; forcing the formula past it produces numbers nobody should quote against.
The estimate is far from the quote I received. Which is right?
Look at which line differs. Die sets are standard parts with transparent pricing, so the gap is usually in machining hours and steel grade. If the quote is more than double, ask whether it includes carbide, nitrogen springs or automatic feeding. If it is half, check die life and after-sales — cheap tooling shows its real cost during production, not at PO.