Blow Mould Cost Estimator
The blow moulding cost calculator takes "blow mould cost" as an input — but quotes usually just say "one mould". This tool answers what that means: by part volume and cavity count it splits the cavity block, frame, neck inserts, handle insert, cooling circuits and trial shots, applies a material and output-tier factor, and returns cost per shot so you can paste it back into the part cost calculator.
1. Inputs
| Cavity block (roughing, cavity surface, parting line fitting) | — CNY |
| Frame / base plate / guide pins | — CNY |
| Neck inserts (per cavity) | — CNY |
| Handle insert | — CNY |
| Cooling circuits (drilling, plugs, pressure test) | — CNY |
| Trial shots (machine time) | — CNY |
| Cavity factor | — × |
| Combined factor (material × output tier) | — × |
| Cost per shot (total ÷ reference life) | — CNY/shot |
| Reference life of this material | — shots |
Put "cost per shot" into the blow moulding cost calculator (mould cost ÷ life) to get this mould's contribution to the unit cost. Life is the material reference value; real life also depends on cooling water quality and colour changes.
±35%. Blow moulds are quoted discretely: the same 1 L bottle can differ by 50–100% between north and south China, between a cosmetics-bottle shop and a jerry-can shop, with or without flow analysis and quick-change hardware. Use this to check the order of magnitude and to see which line eats the budget — not to argue a quote down to the cent.
Formulas
cavity factor = 1 + 0.55 × (cavities − 1)
cavity block(CNY) = (11250 + 6750 × volume L) × cavity factor
frame(CNY) = (3000 + 900 × volume L) × (1 + 0.25 × (cavities − 1))
neck inserts(CNY) = 1500 × cavities (only when ticked)
handle insert(CNY)= 2200 (only when ticked)
cooling(CNY) = 800 + 400 × volume L
trial shots(CNY) = 3 × 2 h × 400 CNY/h = 2400
total(CNY) = sum of six lines × material factor × output tier factor
per shot(CNY) = total ÷ reference life (300k / 750k / 1M shots) Why volume rather than area or perimeter? A blow mould is hogged out: the cavity is a half-bottle dug into a block, so bigger volume means a thicker blank, more roughing and longer cooling circuits. Stamping dies scale with area, extrusion dies with perimeter — pick the wrong basis and the estimate is off by an order of magnitude. A flat shampoo bottle and a slim water bottle of the same 1 L differ by less than 20%, because the removed volume is nearly identical.
What the inputs mean
- Part volume — nominal capacity is enough. 0.1 L pharma bottles and 20 L drums are in range; above ~20 L you are in structural blow moulding with parison wall control, which this tool does not include.
- Cavities — 1–4 in practice. Each extra cavity multiplies the cavity block by 1.55 (not 2: frame and cooling are shared) and adds one neck insert. Beyond 4 cavities parison control struggles to keep wall thickness even, so the tool refuses it.
- Cavity material — aluminium machines fast and conducts heat well, the standard for small runs and prototypes; beryllium copper cools fastest and is used for transparent parts where flow marks must be avoided; tool steel is for PE drums in the million-piece range.
- Annual output — higher volume justifies more cooling, wear inserts and heat treatment, hence 0.95–1.12. The factor adjusts the level of investment, not the structure.
- Neck insert — threads, tamper bands and spout sealing faces need a replaceable insert. When it wears you swap the insert, not the mould.
- Handle insert — handles cannot be blown as part of the body; an insert is placed in the mould and the body welds onto it. It is machined separately and priced once per mould.
Worked examples
1 L bottle, single cavity, aluminium, neck insert, no handle, 300k pcs/year (page defaults):
| Cavity factor | 1 + 0.55 × 0 = 1.00 |
| Cavity block | (11250 + 6750 × 1) × 1.00 = 18,000 CNY |
| Frame | (3000 + 900 × 1) × 1 = 3,900 CNY |
| Neck insert | 1500 × 1 = 1,500 CNY |
| Cooling | 800 + 400 × 1 = 1,200 CNY |
| Trial shots | 3 × 2 × 400 = 2,400 CNY |
| Subtotal | 18,000 + 3,900 + 1,500 + 1,200 + 2,400 = 27,000 CNY |
| Total | 27,000 × (1.00 × 1.00) = ¥27,000 |
| Per shot | 27,000 ÷ 300,000 = ¥0.09/shot |
Same formulas with other conditions:
| 5 L chemical drum, 2 cavities, tool steel, neck + handle, 2M pcs/year | block 45,000 × 1.55 = 69,750; frame 7,500 × 1.25 = 9,375; neck 3,000; handle 2,200; cooling 2,800; trial 2,400 → 89,525 × (1.90 × 1.12 = 2.128) = ¥190,509, ¥0.19/shot |
| 0.5 L bottle, 4 cavities, beryllium copper, neck insert, no handle, 50k pcs/year | block 14,625 × 2.65 = 38,756.25; frame 3,450 × 1.75 = 6,037.50; neck 6,000; cooling 1,000; trial 2,400 → 54,193.75 × (1.55 × 0.95 = 1.4725) = ¥79,800, ¥0.11/shot |
| Drop the handle insert from the 5 L drum | 89,525 − 2,200 = 87,325 × 2.128 = ¥185,828 (saves ¥4,681) |
Note the second row: a 0.5 L bottle costs nearly three times a 1 L one — not because of size, but because of 4 cavities + beryllium copper (2.65 × 1.55). Conversely, if a quote for a 0.5 L bottle lands near a single-cavity 1 L price, suspect a single-cavity mould — you would get a quarter of the output.
Four common mistakes
- Estimating volume from outside dimensions — the cavity follows the internal volume; a flat bottle's outside is far bigger, inflating the block by 30%+.
- Multiplying a single-cavity price by the cavity count — frame, cooling and trial are shared; the 1.55 factor encodes that.
- Forgetting the handle insert — jug quotes often list it separately; miss it and the mould budget overruns later.
- Treating the mould as a one-off — amortise it over life. Use the blow moulding cost calculator's mould amortisation, or paste in the per-shot figure here.
Not included
- Design work and flow analysis (typically 8–15% of mould cost, quoted separately)
- Parison wall distribution systems (PWDS), hydraulic servo heads and other head hardware
- Quick-change systems and robot take-out grippers
- Trial-shot scrap and machine occupancy beyond machine time
- Chrome plating, polishing rework, freight and taxes
- Injection moulds and extrusion dies — different structure and pricing, see injection mould cost and extrusion die cost
FAQ
Why is a 2-cavity mould not twice a 1-cavity one?
Because the expensive shared parts — frame, base plate, guides, cooling circuits, trial labour and machine time — cost almost the same for one or two cavities. What doubles is the cavity block and the neck inserts. The 1.55 factor approximates this; past 4 cavities the shared share shrinks and the factor under-estimates, which is why the tool stops at 4.
Aluminium versus tool steel differs by 90% — why?
Life and cooling. Aluminium conducts roughly 150 W/(m·K) against ~30 for tool steel: faster cooling, shorter cycles, but lower hardness, so cavity surfaces scuff after a few hundred thousand shots. Steel reaches a million shots and wins on cost per shot. Decide on total volume: aluminium below 300k parts, steel above 1M, and in between by whether transparency and appearance matter.
The estimate differs a lot from the quote — whom do I trust?
Locate the line that differs. Frame and cooling are fairly transparent; the gap usually sits in cavity machining time and steel grade. If the quote is more than double, ask about flow analysis, imported steel and wall control. If it is half, check cavity count and material — the usual way to cheapen a blow mould is fewer cavities and recycled aluminium, and the money comes back in cycle time and repairs.