Extrusion Die Cost Estimator
The extrusion cost calculator takes die cost as an input, but a quotation rarely says more than "one head". This tool fills that gap: from profile perimeter and wall thickness it splits a tool into die head, breaker plate, bench hours, sizing sleeve and tryout, so you can judge whether a die maker's quote is in the right order of magnitude before you negotiate.
1. Inputs
| Die head (body, flow channel, polishing) | — CNY |
| Breaker plate / support / adapter | — CNY |
| Bench assembly and polishing | — CNY |
| Vacuum sizing sleeve | — CNY |
| Tryout (extruder hours) | — CNY |
| Bench hours | — h |
| Multiplier (steel × output tier) | — × |
±35%. Die heads are quoted, not calculated: the same profile can differ by a factor of two between a pipe specialist and a profile shop, or depending on whether a co-extrusion feedblock is in scope. Use this to place the quote in a band and to see which line is eating the budget — not to argue the last cent.
Formula
Thin-wall factor = √(3 ÷ wall) (3 mm = 1.00)
Die head (CNY) = (1200 + 8 × perimeter) × thin-wall factor
Breaker plate = 600 + 2.5 × perimeter
Bench hours = (12 + 0.05 × perimeter) × (1 + 0.35 × (layers − 1))
Bench cost = bench hours × 260
Sizing sleeve = 400 + 3 × perimeter (0 if not needed)
Tryout = 3 runs × 3 h × 300 CNY/h = 2700
Total = (head + plate + bench + sleeve + tryout) × steel × output tier
Why perimeter and not area? The working surface of an extrusion die is a narrow
ring-shaped channel: melt arrives through the breaker plate, flows around the spider legs and leaves
through the die lip gap. A longer perimeter means a longer channel to mill, polish and lap — and it
has little to do with how bulky the profile looks. A 20 mm square tube and a 20 mm round bar differ
by 20% in perimeter, yet the lip work is nearly identical.
The thin-wall factor √(3 ÷ wall) captures gap width: going from 2 mm to 1 mm wall halves the lip gap,
a polishing wheel no longer fits, and hand lapping pushes the head cost up by about 41%
(√3 ≈ 1.73 versus √1.5 ≈ 1.22).
What each input means
- Perimeter — the length of the outline; for hollow profiles count inner and outer contours. Window profiles, trunking and seals have far more perimeter than a tube of the same weight, and cost correspondingly more.
- Average wall — use a weighted average when walls differ. It sets the lip gap and is the single biggest driver of polishing hours.
- Layers — 1 for single layer; 2 for a skin/core structure such as HDPE over recycled material; 3 when a tie layer is added. Each extra layer multiplies bench hours by 1.35 because the head needs another flow block. The feedblock itself is not included.
- Die steel — 2Cr13 is cheap and needs it for corrosive compounds such as rigid PVC; SKD61 is the general-purpose choice; for high-volume thin-wall profiles, hardening plus nitriding and chrome plating lifts die life from hundreds of thousands of metres to millions.
- Sizing sleeve — pipes and profiles are calibrated under vacuum right after the die; every size change needs a new sleeve. Sheet, rod and board do not need one.
Worked examples
Perimeter 300 mm, wall 2 mm, single layer, SKD61, with sleeve, medium output (the page defaults):
| Thin-wall factor | √(3 ÷ 2) = √1.5 = 1.2247 |
| Die head | (1200 + 8 × 300) × 1.2247 = 3600 × 1.2247 = 4,409 CNY |
| Breaker plate | 600 + 2.5 × 300 = 1,350 CNY |
| Bench hours | 12 + 0.05 × 300 = 27 h → 27 × 260 = 7,020 CNY |
| Sizing sleeve | 400 + 3 × 300 = 1,300 CNY |
| Tryout | 3 × 3 × 300 = 2,700 CNY |
| Subtotal | 4,409.08 + 1,350 + 7,020 + 1,300 + 2,700 = 16,779.08 CNY |
| Total | 16,779.08 × 1.20 = ¥20,135 |
The same job with a few changes:
| Two layers + 2Cr13 + no sleeve + low output | hours 27 × 1.35 = 36.45 h → 9,477 CNY; subtotal 17,936.08 → ×0.92 = ¥16,501 |
| Large profile: 600 mm, 3 mm wall, single layer, 2Cr13, no sleeve, high output | head 6,000 + plate 2,100 + bench 10,920 + tryout 2,700 = 21,720 → ×1.15 = ¥24,978 |
| Thin wall: 1 mm instead of 2 mm | factor √3 = 1.7321 → head 6,235 CNY; subtotal 18,605 → ¥22,326 |
The third row is worth a pause: halving the wall halves the material per metre, but the die gets dearer — a 1 mm lip cannot be polished with a wheel, so hand lapping adds 41%. That is one reason thin-wall profiles never get cheap per metre.
Four mistakes that skew the number
- Using the bounding box as perimeter — perimeter follows the outline, not the box it fits in; window profiles are routinely 50% more.
- Counting the feedblock as die cost — an ABA or ABAB feedblock is usually a separately quoted module; this tool only adds the bench hours each extra layer implies.
- Forgetting that sleeves wear — a sleeve is a consumable and a size change needs a new one; ask for spare pricing. Only one sleeve is counted here.
- Treating the head as a one-off — amortise it into the per-metre cost using the die amortisation line of the extrusion cost calculator.
Not included
- Die design and flow simulation, often quoted at 10%–20% of the tool cost
- Co-extrusion feedblocks, melt pumps, screen changers and other head accessories
- Trial compound scrap and machine time lost to tryout (only extruder hours are counted)
- Re-chroming, polish repairs, freight and tax
- Sheet (coat-hanger) and blown-film dies — different construction, different pricing; out of scope
- Blow molding heads and blow moulds — hollow parts are tooled and priced differently, see the blow molding cost calculator
FAQ
Why do two profiles of the same weight differ so much in die cost?
Because tooling follows perimeter and wall, not weight. One kilogram per metre as a 60 mm round tube is roughly 188 mm of perimeter; the same weight as a thin-wall profile can exceed 400 mm. The longer lip needs more polishing, the breaker plate grows, and the quote follows. Weigh the part for material cost, measure the perimeter for tooling cost.
Why do co-extrusion layers cost 35% more bench time each?
Every layer needs its own flow channel that must not mix before the confluence, so each flow block is machined, lapped and assembled separately; three layers add a tie layer on top. A slight step at the interface shows up as delamination later. The ×1.35 is an empirical average — very thin skins are harder to control than the factor suggests.
The estimate is far from the quote I received. Which is right?
Check which line differs. Breaker plates and sleeves are fairly transparent; the gap is usually in lip polishing hours and steel grade. If the quote is more than double, ask whether a feedblock is included, or whether imported steel and mirror polishing were used. If it is half, confirm lip material and after-sales — a cheap head shows its real cost at the next size change or repair.