Clamp Force & Machine Tonnage Calculator
"We run it on a 250-tonner" versus "a 150-tonner" can be a 40% difference in machine cost. Tonnage is not a judgement call: projected area times cavity pressure is the clamp force, and the machine is the smallest standard size that covers it. This tool also shows how lightly the chosen machine will be loaded.
| Theoretical clamp force | — kN |
| Design clamp force (with safety) | — t |
| Chosen machine clamp | — kN |
| Machine utilisation | — % |
| Headroom | — % |
| Next size up | — t |
Accuracy ±20%. Projected area must include the runner (cold runners take 10–30%), and cavity pressure varies with wall thickness, flow length and material viscosity. This tool checks clamp force only — not shot weight, opening stroke or mould thickness. A machine can be big enough in tonnes and still not accept the mould.
The formula
clamp force (kN) = projected area (cm²) × cavity pressure (MPa) × 0.1
projected area = area per part (with runner) × cavities
design force = clamp force × safety factor
machine tonnage = smallest standard size ≥ design force
utilisation = theoretical force ÷ machine clamp force The 0.1 comes from the units: 1 MPa = 1 N/mm² = 100 N/cm² = 0.1 kN/cm². One tonne of clamp is about 9.81 kN, so 300 kN is roughly a 31-tonne force.
Worked example
50 cm² projected area per part (runner included), 2 cavities, 30 MPa general purpose, 1.15 safety:
| Total projected area | 50 × 2 = 100 cm² |
| Theoretical clamp force | 100 × 30 × 0.1 = 300 kN |
| Design force | 300 × 1.15 = 345 kN ≈ 35.2 t |
| Recommended machine | 50 t (490 kN clamp), 61% utilisation |
| Thin wall at 70 MPa | 700 kN → 805 kN design ≈ 82 t → 100 t machine, 71% utilisation |
| Four cavities | area doubles → 600 kN → 690 kN design ≈ 70 t → 100 t machine |
How tonnage drives cost
Tonnage buys clamp force and platen size, and the hourly rate follows: a 50-tonne machine often runs 30–50 CNY/hour, a 250-tonne 90–150, and anything above 1,000 tonnes starts around 300. At the same cycle, moving from a 250-tonne to a 150-tonne machine can cut machine cost per part by more than 30%.
The reverse is also true: adding a size "for safety" is a permanent tax in machine time and power. Price both options with the machine hour rate calculator, convert to per-part with the cycle time calculator, and the case for a smaller press is either there or it is not.
Four common mistakes
- Using the part area only — the runner is missing, and a cold runner takes 10–30% of the projected area.
- Forgetting the cavity multiplier — four cavities need four times the force, not four parts' worth.
- Reading machine hydraulic pressure as cavity pressure — nozzle and runner losses sit in between.
- Safety factor of 1.0 — mould rigidity, machine accuracy and melt variation eat the margin; 1.1–1.25 is normal.
Not included
- Shot weight and screw diameter checks (too little shot capacity rules the machine out)
- Opening stroke, mould thickness and tie-bar spacing
- Two-shot, multi-colour and insert moulding requirements
- Die casting machine tonnage (same shape, different intensification)
FAQ
Why 61% utilisation instead of a smaller machine?
Standard sizes are discrete: a 35-tonne design force rounds up to the 50-tonne machine. Below about 50% utilisation it is worth changing cavity count or machine series rather than accepting the next size.
How do I pick cavity pressure?
Use flow analysis when you have it. Otherwise: 20 MPa for thick easy-flow parts, 30 general purpose, 40 engineering resins, 50 precision, 70 thin wall high speed. Thinner walls and longer flow paths push the number up.
Why does tonnage jump so fast for thin walls?
Thin walls need higher injection pressure to fill, cavity pressure rises with it, and with the same projected area the clamp force doubles. That is also why thin-wall moulds demand better steel and a stiffer press.